• +1 954 484 9700 Talk to an expert
  • 4180 NW 10 Avenue Ft. Lauderdale, FL-US

COLD ADHESIVE SYSTEMS

Cold adhesive systems engineered for precision dispensing at production speed.

Spraymation cold adhesive systems give manufacturers the dripless precision, pattern repeatability, and long service life that high-speed converting and assembly demand. Built around our patented Electromatic™ applicator platform, our cold adhesive application equipment dispenses water-based glues, latex adhesives, marking fluids, and similar low-to-medium viscosity materials with the kind of accuracy that eliminates waste, prevents bond failures, and stays in spec for decades, with full-size and mid-size applicators rated for 200 million dispensing cycles before refurbishment.

The Problem

Solving the problems that plague cold adhesive application.

Cold adhesive dispensing presents its own set of challenges. Water-based glues and latex adhesives can dry inside conventional applicators and clog nozzles. Inconsistent dispensing causes weak bonds, scrap, and rework. Drool and stringing contaminate products and create cleanup overhead. Worn seals leak. And every minute spent rebuilding a gun is a minute the line isn’t producing.

Spraymation cold adhesive application equipment is engineered specifically to eliminate these problems. The Electromatic™ applicator at the heart of every system has only one moving part, no dynamic seals to degrade, all-stainless-steel wetted parts for compatibility with aggressive adhesive chemistries, and a positive shut-off design that is completely dripless no matter how fast the gun cycles. Straight-line fluid flow with no trapped areas keeps adhesive moving and prevents the dry-out that clogs ordinary equipment. When service is needed, the entire fluid section comes out as a single replaceable unit in seconds — without removing the gun from the line.

Because actuation is positive-displacement, every cycle delivers the same metered volume regardless of line speed, which is what makes highly accurate micro-deposits repeatable rather than approximate.

The result is a cold adhesive system that runs longer between maintenance intervals, dispenses with the repeatability your quality team requires, and stays in production for decades rather than years.

No nozzle clogging.

Straight-line flow with no trapped areas prevents the dry-out that clogs conventional water-based and latex adhesive guns.

No stringing or drool.

Patented seat-and-needle geometry delivers positive shut-off — dripless even at the highest cycle speeds.

No weak bonds.

0.1 ms timing resolution and millisecond actuation repeatability place adhesive exactly where it belongs, every cycle.

No seal leaks.

One moving part, no dynamic seals, no packings. Fluid section replaces as a complete unit in seconds.

Four elements, engineered to work as one.

How a Cold System Works.

Every Spraymation cold adhesive system is assembled from four coordinated elements, specified together for your fluid, your pattern, and your line speed. Complete systems are available with CE compliance.

[01]

Fluid source

A low-pressure system built around an ASME stainless steel pressure tank, or a high-pressure system built around a stainless steel high-ratio pump — selected by viscosity, required flow rate, and operating pressure.

[02]

Distribution

A manifold routes fluid from the source to every applicator on the line, holding supply pressure consistent across heads.

[03]

Applicators and tips

Electromatic™ applicators paired with the tip that produces your pattern — single extrusion, multiple-line extrusion, airless spray, air-atomizing spray, air-dispersed swirl, or slot coating.

[04]

Controls

Your existing PLC, or Spraymation timers and gun drivers — with separate air-atomizing controls for solenoid valves where the application requires them.

Our Cold Adhesive Systems

A complete family — from miniature precision to wide-web manifolds.

Spraymation offers a complete family of cold adhesive systems, from miniature precision applicators for small-dot placement to multi-head manifolds for wide-web bonding. Each system pairs the right Electromatic™ applicator with the right fluid handling, controls, and accessories for your application.

Electromatic™ XV Automatic Applicator (Cold)

Full-size unheated extrusion and airless spray applicator for cold adhesives, marking fluids, perfumes, silicones, and similar materials requiring small repetitive amounts applied accurately at high speed. Uses extrusion tips for dots and lines, or spray nozzles for atomized patterns. Suitable for use with pressure tanks or pumping systems depending on viscosity and flow requirements.

Format:

Full-Size Unheated

Output:

Extrusion · Airless

Delivery:

Pressure Tank or Pump

Max Pressure:

2,500 PSI

Speed:

2,000 cycles/min

Service Life:

200 million shots

A smaller, lighter, lower-cost version of the full-size Electromatic™ XV with similar performance characteristics. The 99200 Series is well suited for moderate-speed applications with low to medium viscosities up to 6,000 cps and operating pressures under 2,000 PSI. The reduced weight makes it ideal for reciprocating or moving-applicator installations. Models 99201 and 99221 accommodate flat-back tips and 3/8-24 screw-on tips respectively. The ½-20 JIC fluid inlet and standard tip compatibility make it a direct integration option for existing Spraymation cold adhesive systems.

Viscosity:

Up to 6,000 cPs

Pressure:

Under 2,000 PSI

Inlet:

½-20 JIC

Speed:

1,800 cycles/min

Weight:

15 oz

Service Life:

200 million shots

Air-atomized automatic spray head that applies precise amounts of low-viscosity cold fluids at room temperature, producing patterns ranging from a fine mist to a heavy wet coat by mixing air and fluid at the spray head. Ideal for coating applications, surfactant spraying, fragrance application, and any cold fluid requiring full-coverage spray rather than discrete dots or lines.

Atomization:

External Air

Pattern Range:

Fine Mist → Wet Coat

Fluids:

Low-Viscosity Cold

Nozzle Patterns:

15° · 45° · 60° cone/fan

Speed:

2,000 cycles/min

Service Life:

200 million shots

Mid-size air-atomized applicator for low-viscosity cold fluids applied in controlled patterns, delivering the same atomized capability as the full-size 24 series in a lighter, more compact package. The reduced weight suits reciprocating and moving-applicator installations where an air-atomized pattern is required.

Format:

Mid-Size Air-Atomized

Pattern:

Dots · Lines · Beads · Fan

Weight:

15 oz

Max Pressure:

100 PSI

Speed:

1,800 cycles/min

Service Life:

200 million shots

Multi-outlet head series for applications requiring multiple parallel lines or dots of cold adhesive or similar material across a single web or assembly. Patented Electromatic™ design principles applied to a multi-line format, with consistent material volume across every outlet.

Outlets:

Multiple Parallel

Output:

Lines · Dots

Volume:

Consistent Across Outlets

Custom multiple-outlet configurations for cold adhesive applications that require non-standard center distances, specialized nozzles, or unique manifold arrangements.

Configuration:

Custom Centers

Nozzles:

Specialized

Hot Variant:

XXX Available

Miniature extrusion applicator with carbide plunger tips and stainless steel seats for extended service life, redesigned coils and springs for increased operating speeds, and broader viscosity tolerance. Ideal for precision dot placement and small-form-factor assembly applications.

Plunger Tips:

Carbide

Seats:

Stainless Steel

Use Case:

Precision Dot Placement

Max Pressure:

200 PSI

Speed:

1,200 cycles/min

Weight:

6 oz

Service Life:

100 million shots

Miniature spray applicator for compact, high-speed atomized application of cold fluids where space is constrained and pattern precision is critical.

Format:

Compact Spray

Speed:

High-Speed Cycle

Use Case:

Space-Constrained

Nozzle Patterns:

15° · 45° · 60° cone/fan

Max Pressure:

100 PSI

Weight:

8 oz

Service Life:

100 million shots

Handheld applicator for manual cold adhesive dispensing — repair work, short runs, hand assembly, and any application where an operator places the bead. All-stainless-steel wetted parts and the same tip compatibility as our automatic applicators, in a manually triggered format requiring no electrical supply.

Format:

Handgun

Pattern:

Dots · Lines · Beads · Airless Fan

Max Pressure:

2,000 PSI

Actuation:

Manual

Service Life:

50 million shots

Available with extensions to reach confined areas, commonly used for coating the inside of beverage cans and similar enclosed-space applications.

Access:

Confined Areas

Reach:

Extension-Equipped

Common Use:

Beverage Can Interior

Three-head, eight-head, and larger common manifolds with specified or adjustable center distances for wide-web cold adhesive coating applications. Each manifold includes shut-off valves, electrical gun cords, and matched fluid hoses.

Heads:

3 · 8 · Larger

Centers:

Fixed or Adjustable

Includes:

Valves · Cords · Hoses

Applicator Comparison

Specify by pressure, speed, and service life.

Every Electromatic™ cold applicator shares the same core design — one moving part, no dynamic seals, all-stainless-steel wetted parts. The differences are size, pressure capability, cycle speed, and pattern type.

Series Size Pattern Max Pressure Max Speed Service Life Voltage Weight
15 Full size Dots, lines, multiple beads, airless fan 2,500 PSI 2,000 cycles/min · on-time <2 ms 200 million shots 120 VAC or 24 VDC (driver required) 2 lbs · 4.5 × 3 × 1.75 in
24 Full size 15° · 45° · 60° cone/fan (air atomized) 100 PSI 2,000 cycles/min · on-time <2 ms 200 million shots 120 VAC or 24 VDC (driver required) 2 lbs · 5 × 3 × 1.75 in
16 Mid size Dots, lines, multiple beads, airless fan 2,000 PSI 1,800 cycles/min · on-time <4 ms 200 million shots 24 VDC (1.6 A) 15 oz · 3.7 × 2.4 × 1.4 in
34 Mid size Dots, lines, multiple beads, fan (air atomized) 100 PSI 1,800 cycles/min · on-time <4 ms 200 million shots 24 VDC (1.6 A) 15 oz · 4.3 × 2.4 × 1.4 in
130 Mini Dots, lines, multiple beads 200 PSI 1,200 cycles/min · on-time <5 ms 100 million shots 24 VDC (20 W · 0.8 A) 6 oz · 3.3 × 2.2 × 1 in
330 Mini 15° · 45° · 60° cone/fan (air atomized) 100 PSI 1,200 cycles/min · on-time <5 ms 100 million shots 24 VDC (20 W · 0.8 A) 8 oz · 3.9 × 2.2 × 1 in
36 Handgun Dots, lines, multiple beads, airless fan 2,000 PSI Manual 50 million shots None 8 oz · 8 × 9 × 1.4 in

Series

15

Size

Full size

Pattern

Dots, lines, multiple beads, airless fan

Max Pressure

2,500 PSI

Max Speed

2,000 cycles/min · on-time <2 ms

Service Life

200 million shots

Voltage

120 VAC or 24 VDC (driver required)

Weight

2 lbs · 4.5 × 3 × 1.75 in

Series

24

Size

Full size

Pattern

15° · 45° · 60° cone/fan (air atomized)

Max Pressure

100 PSI

Max Speed

2,000 cycles/min · on-time <2 ms

Service Life

200 million shots

Voltage

120 VAC or 24 VDC (driver required)

Weight

2 lbs · 5 × 3 × 1.75 in

Series

16

Size

Mid size

Pattern

Dots, lines, multiple beads, airless fan

Max Pressure

2,000 PSI

Max Speed

1,800 cycles/min · on-time <4 ms

Service Life

200 million shots

Voltage

24 VDC (1.6 A)

Weight

15 oz · 3.7 × 2.4 × 1.4 in

Series

34

Size

Mid size

Pattern

Dots, lines, multiple beads, fan (air atomized)

Max Pressure

100 PSI

Max Speed

1,800 cycles/min · on-time <4 ms

Service Life

200 million shots

Voltage

24 VDC (1.6 A)

Weight

15 oz · 4.3 × 2.4 × 1.4 in

Series

130

Size

Mini

Pattern

Dots, lines, multiple beads

Max Pressure

200 PSI

Max Speed

1,200 cycles/min · on-time <5 ms

Service Life

100 million shots

Voltage

24 VDC (20 W · 0.8 A)

Weight

6 oz · 3.3 × 2.2 × 1 in

Series

330

Size

Mini

Pattern

15° · 45° · 60° cone/fan (air atomized)

Max Pressure

100 PSI

Max Speed

1,200 cycles/min · on-time <5 ms

Service Life

100 million shots

Voltage

24 VDC (20 W · 0.8 A)

Weight

8 oz · 3.9 × 2.2 × 1 in

All applicators: one moving part, no dynamic seals, all-stainless-steel wetted parts. Service life is rated dispensing shots before factory refurbishment.

The pattern is made at the tip.

Tips & Nozzles

The applicator meters the fluid; the tip decides what the pattern looks like. Spraymation manufactures the full range of extrusion, spray, and slot tips in stainless steel, and makes tips to order in effectively unlimited variations for applications the standard range doesn’t cover.

Tip type Orifices Orifice size Angles Material Pattern produced
Single orifice extrusion One 0.006–0.030 in 0° (on applicator axis) Stainless steel Single dot or bead
Multiple orifice extrusion 2–6 holes 0.006–0.020 in In-line for parallel beads, or radial at a specified angle Stainless steel Group of lines or dots, in-line or radial
Side outlet extrusion 1, 2, or 3 0.001–0.020 in 45° and 90° standard Stainless steel Up to 3 lines or dots dispensed perpendicular to the applicator axis
Airless spray One 0.009–0.032 in 15°–110° Stainless steel or carbide insert Airless fan pattern (requires high pressure)
Slot tip (ribbon) One rectangular slot Slots up to 1 in wide; wider available 0° Stainless steel Thin ribbon, dispensed with the tip in contact with the material
Handgun extrusion One 0.015–0.050 in 0° Stainless steel Hand-dispensed single dot or bead
Extended extrusion One 0.006–0.030 in 0° Stainless steel Single dot or bead in a tight space

Tip type

Single orifice extrusion

Orifices

One

Orifice size

0.006–0.030 in

Angles

0° (on applicator axis)

Material

Stainless steel

Pattern produced

Single dot or bead

Tip type

Multiple orifice extrusion

Orifices

2–6 holes

Orifice size

0.006–0.020 in

Angles

In-line for parallel beads, or radial at a specified angle

Material

Stainless steel

Pattern produced

Group of lines or dots, in-line or radial

 

Tip type

Side outlet extrusion

Orifices

1, 2, or 3

Orifice size

0.001–0.020 in

Angles

45° and 90° standard

Material

Stainless steel

Pattern produced

Up to 3 lines or dots dispensed perpendicular to the applicator axis

Tip type

Airless spray

Orifices

One

Orifice size

0.009–0.032 in

Angles

15°–110°

Material

Stainless steel or carbide insert

Pattern produced

Airless fan pattern (requires high pressure)

Tip type

Airless spray

Orifices

One

Orifice size

0.009–0.032 in

Angles

15°–110°

Material

Stainless steel or carbide insert

Pattern produced

Airless fan pattern (requires high pressure)

Tip type

Slot tip (ribbon)

Orifices

One rectangular slot

Orifice size

Slots up to 1 in wide; wider available

Angles

0°

Material

Stainless steel

Pattern produced

Thin ribbon, dispensed with the tip in contact with the material

Tip type

Handgun extrusion

Orifices

One

Orifice size

0.015–0.050 in

Angles

0°

Material

Stainless steel

Pattern produced

Hand-dispensed single dot or bead

Tip type

Extended extrusion

Orifices

One

Orifice size

0.006–0.030 in

Angles

0°

Material

Stainless steel

Pattern produced

Single dot or bead in a tight space

Orifice size must not exceed the applicator’s seat size. Our engineering team will confirm the right tip for your fluid, pattern, and applicator.

WHY SPRAYMATION

Reasons our cold adhesive equipment outlasts the rest.

01

Dripless, positive shut-off.

The patented Electromatic™ seat-and-needle geometry eliminates the stringing, drool, and product contamination that plague conventional cold adhesive guns.

02

One moving part, no dynamic seals.

No packings to wear, no seals to leak, no rebuilds at six-month intervals. The fluid section comes out as a single replaceable unit in seconds.

03

All-stainless-steel wetted parts.

Compatible with the full range of water-based adhesives, latex glues, and aggressive chemistries that degrade conventional components.

04

Straight-line fluid flow.

No trapped areas where adhesive can dry out, char, or accumulate — critical for water-based and latex glues that solidify in dead zones.

05

Integral solenoid actuation.

No external air valves required for the standard Electromatic™ series — instantaneous response and millisecond repeatability for high-speed lines.

06

Built for decades, not years.

Full-size and mid-size Electromatic™ applicators are rated for 200 million dispensing shots before refurbishment, and mini applicators for 100 million. Spraymation cold adhesive systems installed 40 or more years ago are still in production today.

07

Positive-displacement micro-deposits.

Accurate, repeatable positive-displacement dispensing for applications that require highly accurate micro deposits — the same metered volume every cycle, independent of line speed.

08

Every pattern from one platform.

Dots, lines, multiple lines, airless spray, air-atomizing spray, air-dispersed swirl, and slot coating — all from the same Electromatic™ applicator family and the same control architecture.

09

ISO 9001:2015 certified.

With CE declarations and Low Voltage Directive compliance available for European installations. Family-owned and manufacturing in Fort Lauderdale for more than 60 years, ISO certified for over 20.

Applications

Where our cold adhesive systems excel.

Spraymation cold adhesive application equipment is at work across paper converting, hygiene product manufacturing, consumer goods, beverage can production, and dozens of other high-speed converting and assembly operations where consistency and cleanliness matter.

If your cold adhesive application has unusual fluid characteristics, web width requirements, or environmental constraints, our engineering team can design a custom solution — from specialized manifolds to extension-equipped applicators for confined spaces to recirculating-path configurations for fluids that require continuous flow.

Paper Towel & Toilet Paper Core Gluing

Tail-Tie Spray & Linear Tail-Tie

Multi-Ply Tissue Bonding

Premium Napkin & Tablecloth Assembly

Disposable Hygiene Product Manufacturing

Beverage Can Interior Coating

Packaging & Case Sealing

Fragrance & Surfactant Application

Marking Fluid Dispensing

Perfume Application

Slot & Ribbon Coating

Hand Assembly & Repair (Handgun)

Complete Your System

Every component, engineered under one roof.

Every Spraymation cold adhesive system can be configured with the controls, fluid handling, and accessories needed for a complete turnkey solution.

Pattern Controllers & Timers

3480 Pattern Controllers and 3400 Series DC Timers for independent control of up to four applicators with 0.1 ms timing resolution.

Available as a basic single-applicator DELAY/ON timer or a four-channel controller for complex patterns with multiple on/off switching. Supports shaft-encoded position programming in inches — so pattern placement follows actual machine travel rather than elapsed time — and multiple applicators can run from a single timer.

Pressure Tanks & Fluid Handling

ASME-approved low-pressure tanks in 2, 5, and 10 gallon capacities with optional low-level controls and adjustable-speed agitators, plus portable low-pressure pumps with regulators and tank dollies for mobile applications.

Stainless steel construction, rated to 100 PSI maximum, with DC power supply and CE approval. Accessories include low-level switch, agitator, air gauge, regulator, filter, quick disconnect, and a choice of EPDM or Viton seals for fluid compatibility.

Applicator Heads

Browse the complete Electromatic™ applicator family for replacement heads, expansion components, or custom configurations across the full product line.

Gun Drivers

Drivers that supply the optimum voltage and current to get full performance from full-size and mid-size Electromatic™ applicators. Accelerating voltages on both open and close reduce actuation times for higher line speeds. Easy PLC interface, 120 or 240 volt operation.

High-Pressure Pumps

Stainless steel high-ratio pumps for airless spray and high-viscosity cold adhesive delivery:

  • 50:1 — 1.25 gal/min — 2,500 PSI
  • 28:1 — 2.0 gal/min — 2,500 PSI
  • 5:1 — 4 gal/min — 500 PSI

Available in wall-mount, 55-gallon drum, and 5-gallon pail configurations. Accessories include control valve, automatic fluid pressure release, air gauge, regulator, and filter.

FAQ

Common questions about cold adhesive application equipment.

Quick answers to the questions we get most often about Spraymation cold adhesive systems, Electromatic™ applicators, and fluid handling integration.

Don’t see your question? Our engineering team responds within one business day.

What types of cold adhesives can Spraymation systems dispense?

Our cold adhesive systems handle a broad range of materials including water-based glues, latex adhesives, PVA adhesives, marking fluids, perfumes, fragrances, surfactants, low-viscosity silicones, and similar fluids. The Electromatic™ XVI mid-size handles low to medium viscosities up to 6,000 cps, while full-size and air-operated configurations accommodate higher-viscosity and higher-flow requirements. If you have a specific adhesive chemistry, our engineering team can confirm compatibility and recommend the right applicator configuration.

The Electromatic™ applicator at the core of every Spraymation cold adhesive system uses a patented design with only one moving part, no dynamic seals, all-stainless-steel wetted parts, and a positive dripless shut-off. Conventional adhesive application equipment typically relies on packings, dynamic seals, and external air valves that wear, leak, and require frequent rebuilds — and conventional guns are particularly prone to dry-out and clogging with water-based adhesives. Our straight-line flow design eliminates these failure modes, which is why Spraymation cold adhesive equipment routinely stays in production for decades.

Yes. Used with appropriate extrusion tips or spray nozzles and a Spraymation 3480 Pattern Controller or 3400 Series DC Timer, Electromatic™ applicators place dots, continuous lines, interrupted lines, multiple parallel lines, or full atomized spray patterns with extreme accuracy. The full pattern range across the platform covers dots, lines, multiple lines and dots, airless spray, air-atomizing spray, air-dispersed swirl, and slot coating. The Electromatic™ XV is configured for extrusion or airless spray, the XXIV handles air-atomized spray from fine mist to wet coat, and the XX and XXV series handle multiple parallel outlets for wide-web applications.

Capability depends on the specific applicator. The Electromatic™ XVI mid-size handles low to medium viscosities up to 6,000 cps at operating pressures under 2,000 PSI. Full-size Electromatic™ XV applicators handle broader ranges including higher-viscosity cold materials. Air-operated high-volume variants are available for pressures up to 5,000 PSI and very high flow rates with the highest viscosities. Contact our engineering team with your fluid viscosity and we’ll recommend the right configuration.

Yes — custom cold adhesive application equipment is a core part of what we do. We routinely build multi-head manifolds with specified or adjustable center distances for wide-web applications, applicators with extensions for confined-area access such as inside beverage cans, recirculating-path configurations for fluids requiring continuous flow, and one-of-a-kind systems for applications other manufacturers won’t take on. Send us your line speed, web width, fluid specifications, and pattern requirements and our engineering team will recommend a solution.

The Electromatic™ design dramatically simplifies maintenance — the entire fluid section can be removed and replaced as a unit in seconds without taking the gun off the line, and there are no packings or dynamic seals to degrade and replace. We maintain an extensive inventory of spare parts and supplies, offer factory rebuild and gun exchange programs, and provide remote technical support by phone, email, and Zoom, with on-site service available when needed.

Most cold adhesive applications use either a pressure tank or a pumping system depending on viscosity, required flow rate, and operating pressure. Spraymation offers ASME-approved low-pressure tanks in 2, 5, and 10 gallon capacities with optional low-level controls and adjustable-speed agitators for water-based and latex adhesives that require continuous mixing. Tanks are stainless steel, rated to 100 PSI, CE approved, and available with EPDM or Viton seals depending on fluid compatibility. Portable low-pressure pumps with regulators are available for spray applications, and tank dollies provide mobility for shared-use installations. For high-pressure airless spray, our stainless steel balanced-ratio pumps are rated for continuous duty up to 2,500 PSI, in 50:1, 28:1, and 5:1 ratios and wall-mount, drum, or pail configurations.

In most cases, yes. The 3480 Pattern Controller and 3400 Series DC Timers accept inputs from passive contacts, DC voltage signals, photocells, and open collectors, which covers the vast majority of production line control architectures. For specialized control integration, our engineering team can design custom control packages, including stainless steel enclosures and DIN-format temperature controllers.

Full-size and mid-size Electromatic™ applicators are rated for 200 million dispensing shots before factory refurbishment. Mini applicators are rated for 100 million shots, and handguns for 50 million. Those figures are a function of the core design — one moving part, no dynamic seals or packings, and all-stainless-steel wetted parts — and they’re the reason Spraymation cold adhesive systems installed 40 or more years ago are still in production today. When refurbishment does come due, we offer factory rebuild and gun exchange programs.

Spraymation manufactures single-orifice extrusion tips (0.006–0.030 in), multiple-orifice extrusion tips in 2 to 6 holes (0.006–0.020 in), side-outlet tips that dispense perpendicular to the applicator axis in 45° and 90° configurations, airless spray tips (0.009–0.032 in) in fan angles from 15° to 110°, slot tips for ribbon dispensing in widths up to 1 inch and wider on request, handgun extrusion tips (0.015–0.050 in), and extended extrusion tips for dispensing into tight spaces. All are stainless steel, with carbide inserts available on airless spray tips. Orifice size cannot exceed the applicator’s seat size — send us your fluid, pattern, and applicator and we’ll confirm the right tip.

A low-pressure system feeds applicators from an ASME stainless steel pressure tank rated to 100 PSI, which suits lower-viscosity fluids, lower flow rates, and applications that benefit from agitation. A high-pressure system uses a stainless steel high-ratio pump — 50:1 at 1.25 gal/min and 2,500 PSI, 28:1 at 2.0 gal/min and 2,500 PSI, or 5:1 at 4 gal/min and 500 PSI — and is required for airless spray and for higher-viscosity or higher-flow applications. Viscosity, required flow rate, and operating pressure determine which is right for your line.

Yes. A single Spraymation timer can drive multiple applicators, and our four-channel controllers handle complex patterns with multiple on and off points per cycle. For applications where pattern placement has to follow machine travel rather than elapsed time, shaft-encoded position programming lets you program placement in inches. Systems can also run directly from your existing PLC.

Get Started

Need cold adhesive application equipment that dispenses cleanly, shift after shift, year after year??

Talk to a Spraymation engineer about the right Electromatic™ applicator, fluid handling, and pattern control configuration for your line. We’ll help you specify a system that eliminates waste, prevents bond failures, and stays in service for decades.

Or call us directly +1 954 484 9700

Secret Link