COLD ADHESIVE SYSTEMS
Spraymation cold adhesive systems give manufacturers the dripless precision, pattern repeatability, and long service life that high-speed converting and assembly demand. Built around our patented Electromatic™ applicator platform, our cold adhesive application equipment dispenses water-based glues, latex adhesives, marking fluids, and similar low-to-medium viscosity materials with the kind of accuracy that eliminates waste, prevents bond failures, and stays in spec for decades, with full-size and mid-size applicators rated for 200 million dispensing cycles before refurbishment.
Cold adhesive dispensing presents its own set of challenges. Water-based glues and latex adhesives can dry inside conventional applicators and clog nozzles. Inconsistent dispensing causes weak bonds, scrap, and rework. Drool and stringing contaminate products and create cleanup overhead. Worn seals leak. And every minute spent rebuilding a gun is a minute the line isn’t producing.
Spraymation cold adhesive application equipment is engineered specifically to eliminate these problems. The Electromatic™ applicator at the heart of every system has only one moving part, no dynamic seals to degrade, all-stainless-steel wetted parts for compatibility with aggressive adhesive chemistries, and a positive shut-off design that is completely dripless no matter how fast the gun cycles. Straight-line fluid flow with no trapped areas keeps adhesive moving and prevents the dry-out that clogs ordinary equipment. When service is needed, the entire fluid section comes out as a single replaceable unit in seconds — without removing the gun from the line.
Because actuation is positive-displacement, every cycle delivers the same metered volume regardless of line speed, which is what makes highly accurate micro-deposits repeatable rather than approximate.
The result is a cold adhesive system that runs longer between maintenance intervals, dispenses with the repeatability your quality team requires, and stays in production for decades rather than years.
Straight-line flow with no trapped areas prevents the dry-out that clogs conventional water-based and latex adhesive guns.
Patented seat-and-needle geometry delivers positive shut-off — dripless even at the highest cycle speeds.
0.1 ms timing resolution and millisecond actuation repeatability place adhesive exactly where it belongs, every cycle.
One moving part, no dynamic seals, no packings. Fluid section replaces as a complete unit in seconds.
Four elements, engineered to work as one.
Every Spraymation cold adhesive system is assembled from four coordinated elements, specified together for your fluid, your pattern, and your line speed. Complete systems are available with CE compliance.
[01]
A low-pressure system built around an ASME stainless steel pressure tank, or a high-pressure system built around a stainless steel high-ratio pump — selected by viscosity, required flow rate, and operating pressure.
[02]
A manifold routes fluid from the source to every applicator on the line, holding supply pressure consistent across heads.
[03]
Electromatic™ applicators paired with the tip that produces your pattern — single extrusion, multiple-line extrusion, airless spray, air-atomizing spray, air-dispersed swirl, or slot coating.
[04]
Your existing PLC, or Spraymation timers and gun drivers — with separate air-atomizing controls for solenoid valves where the application requires them.
Spraymation offers a complete family of cold adhesive systems, from miniature precision applicators for small-dot placement to multi-head manifolds for wide-web bonding. Each system pairs the right Electromatic™ applicator with the right fluid handling, controls, and accessories for your application.
Full-size unheated extrusion and airless spray applicator for cold adhesives, marking fluids, perfumes, silicones, and similar materials requiring small repetitive amounts applied accurately at high speed. Uses extrusion tips for dots and lines, or spray nozzles for atomized patterns. Suitable for use with pressure tanks or pumping systems depending on viscosity and flow requirements.
Format:
Full-Size Unheated
Output:
Extrusion · Airless
Delivery:
Pressure Tank or Pump
Max Pressure:
2,500 PSI
Speed:
2,000 cycles/min
Service Life:
200 million shots
A smaller, lighter, lower-cost version of the full-size Electromatic™ XV with similar performance characteristics. The 99200 Series is well suited for moderate-speed applications with low to medium viscosities up to 6,000 cps and operating pressures under 2,000 PSI. The reduced weight makes it ideal for reciprocating or moving-applicator installations. Models 99201 and 99221 accommodate flat-back tips and 3/8-24 screw-on tips respectively. The ½-20 JIC fluid inlet and standard tip compatibility make it a direct integration option for existing Spraymation cold adhesive systems.
Viscosity:
Up to 6,000 cPs
Pressure:
Under 2,000 PSI
Inlet:
½-20 JIC
Speed:
1,800 cycles/min
Weight:
15 oz
Service Life:
200 million shots
Air-atomized automatic spray head that applies precise amounts of low-viscosity cold fluids at room temperature, producing patterns ranging from a fine mist to a heavy wet coat by mixing air and fluid at the spray head. Ideal for coating applications, surfactant spraying, fragrance application, and any cold fluid requiring full-coverage spray rather than discrete dots or lines.
Atomization:
External Air
Pattern Range:
Fine Mist → Wet Coat
Fluids:
Low-Viscosity Cold
Nozzle Patterns:
15° · 45° · 60° cone/fan
Speed:
2,000 cycles/min
Service Life:
200 million shots
Mid-size air-atomized applicator for low-viscosity cold fluids applied in controlled patterns, delivering the same atomized capability as the full-size 24 series in a lighter, more compact package. The reduced weight suits reciprocating and moving-applicator installations where an air-atomized pattern is required.
Format:
Mid-Size Air-Atomized
Pattern:
Dots · Lines · Beads · Fan
Weight:
15 oz
Max Pressure:
100 PSI
Speed:
1,800 cycles/min
Service Life:
200 million shots
Multi-outlet head series for applications requiring multiple parallel lines or dots of cold adhesive or similar material across a single web or assembly. Patented Electromatic™ design principles applied to a multi-line format, with consistent material volume across every outlet.
Outlets:
Multiple Parallel
Output:
Lines · Dots
Volume:
Consistent Across Outlets
Custom multiple-outlet configurations for cold adhesive applications that require non-standard center distances, specialized nozzles, or unique manifold arrangements.
Configuration:
Custom Centers
Nozzles:
Specialized
Hot Variant:
XXX Available
Miniature extrusion applicator with carbide plunger tips and stainless steel seats for extended service life, redesigned coils and springs for increased operating speeds, and broader viscosity tolerance. Ideal for precision dot placement and small-form-factor assembly applications.
Plunger Tips:
Carbide
Seats:
Stainless Steel
Use Case:
Precision Dot Placement
Max Pressure:
200 PSI
Speed:
1,200 cycles/min
Weight:
6 oz
Service Life:
100 million shots
Miniature spray applicator for compact, high-speed atomized application of cold fluids where space is constrained and pattern precision is critical.
Format:
Compact Spray
Speed:
High-Speed Cycle
Use Case:
Space-Constrained
Nozzle Patterns:
15° · 45° · 60° cone/fan
Max Pressure:
100 PSI
Weight:
8 oz
Service Life:
100 million shots
Handheld applicator for manual cold adhesive dispensing — repair work, short runs, hand assembly, and any application where an operator places the bead. All-stainless-steel wetted parts and the same tip compatibility as our automatic applicators, in a manually triggered format requiring no electrical supply.
Format:
Handgun
Pattern:
Dots · Lines · Beads · Airless Fan
Max Pressure:
2,000 PSI
Actuation:
Manual
Service Life:
50 million shots
Available with extensions to reach confined areas, commonly used for coating the inside of beverage cans and similar enclosed-space applications.
Access:
Confined Areas
Reach:
Extension-Equipped
Common Use:
Beverage Can Interior
Three-head, eight-head, and larger common manifolds with specified or adjustable center distances for wide-web cold adhesive coating applications. Each manifold includes shut-off valves, electrical gun cords, and matched fluid hoses.
Heads:
3 · 8 · Larger
Centers:
Fixed or Adjustable
Includes:
Valves · Cords · Hoses
Every Electromatic™ cold applicator shares the same core design — one moving part, no dynamic seals, all-stainless-steel wetted parts. The differences are size, pressure capability, cycle speed, and pattern type.
| Series | Size | Pattern | Max Pressure | Max Speed | Service Life | Voltage | Weight |
|---|---|---|---|---|---|---|---|
| 15 | Full size | Dots, lines, multiple beads, airless fan | 2,500 PSI | 2,000 cycles/min · on-time <2 ms | 200 million shots | 120 VAC or 24 VDC (driver required) | 2 lbs · 4.5 × 3 × 1.75 in |
| 24 | Full size | 15° · 45° · 60° cone/fan (air atomized) | 100 PSI | 2,000 cycles/min · on-time <2 ms | 200 million shots | 120 VAC or 24 VDC (driver required) | 2 lbs · 5 × 3 × 1.75 in |
| 16 | Mid size | Dots, lines, multiple beads, airless fan | 2,000 PSI | 1,800 cycles/min · on-time <4 ms | 200 million shots | 24 VDC (1.6 A) | 15 oz · 3.7 × 2.4 × 1.4 in |
| 34 | Mid size | Dots, lines, multiple beads, fan (air atomized) | 100 PSI | 1,800 cycles/min · on-time <4 ms | 200 million shots | 24 VDC (1.6 A) | 15 oz · 4.3 × 2.4 × 1.4 in |
| 130 | Mini | Dots, lines, multiple beads | 200 PSI | 1,200 cycles/min · on-time <5 ms | 100 million shots | 24 VDC (20 W · 0.8 A) | 6 oz · 3.3 × 2.2 × 1 in |
| 330 | Mini | 15° · 45° · 60° cone/fan (air atomized) | 100 PSI | 1,200 cycles/min · on-time <5 ms | 100 million shots | 24 VDC (20 W · 0.8 A) | 8 oz · 3.9 × 2.2 × 1 in |
| 36 | Handgun | Dots, lines, multiple beads, airless fan | 2,000 PSI | Manual | 50 million shots | None | 8 oz · 8 × 9 × 1.4 in |
Series
15
Size
Full size
Pattern
Dots, lines, multiple beads, airless fan
Max Pressure
2,500 PSI
Max Speed
2,000 cycles/min · on-time <2 ms
Service Life
200 million shots
Voltage
120 VAC or 24 VDC (driver required)
Weight
2 lbs · 4.5 × 3 × 1.75 in
Series
24
Size
Full size
Pattern
15° · 45° · 60° cone/fan (air atomized)
Max Pressure
100 PSI
Max Speed
2,000 cycles/min · on-time <2 ms
Service Life
200 million shots
Voltage
120 VAC or 24 VDC (driver required)
Weight
2 lbs · 5 × 3 × 1.75 in
Series
16
Size
Mid size
Pattern
Dots, lines, multiple beads, airless fan
Max Pressure
2,000 PSI
Max Speed
1,800 cycles/min · on-time <4 ms
Service Life
200 million shots
Voltage
24 VDC (1.6 A)
Weight
15 oz · 3.7 × 2.4 × 1.4 in
Series
34
Size
Mid size
Pattern
Dots, lines, multiple beads, fan (air atomized)
Max Pressure
100 PSI
Max Speed
1,800 cycles/min · on-time <4 ms
Service Life
200 million shots
Voltage
24 VDC (1.6 A)
Weight
15 oz · 4.3 × 2.4 × 1.4 in
Series
130
Size
Mini
Pattern
Dots, lines, multiple beads
Max Pressure
200 PSI
Max Speed
1,200 cycles/min · on-time <5 ms
Service Life
100 million shots
Voltage
24 VDC (20 W · 0.8 A)
Weight
6 oz · 3.3 × 2.2 × 1 in
Series
330
Size
Mini
Pattern
15° · 45° · 60° cone/fan (air atomized)
Max Pressure
100 PSI
Max Speed
1,200 cycles/min · on-time <5 ms
Service Life
100 million shots
Voltage
24 VDC (20 W · 0.8 A)
Weight
8 oz · 3.9 × 2.2 × 1 in
All applicators: one moving part, no dynamic seals, all-stainless-steel wetted parts. Service life is rated dispensing shots before factory refurbishment.
The applicator meters the fluid; the tip decides what the pattern looks like. Spraymation manufactures the full range of extrusion, spray, and slot tips in stainless steel, and makes tips to order in effectively unlimited variations for applications the standard range doesn’t cover.
| Tip type | Orifices | Orifice size | Angles | Material | Pattern produced |
|---|---|---|---|---|---|
| Single orifice extrusion | One | 0.006–0.030 in | 0° (on applicator axis) | Stainless steel | Single dot or bead |
| Multiple orifice extrusion | 2–6 holes | 0.006–0.020 in | In-line for parallel beads, or radial at a specified angle | Stainless steel | Group of lines or dots, in-line or radial |
| Side outlet extrusion | 1, 2, or 3 | 0.001–0.020 in | 45° and 90° standard | Stainless steel | Up to 3 lines or dots dispensed perpendicular to the applicator axis |
| Airless spray | One | 0.009–0.032 in | 15°–110° | Stainless steel or carbide insert | Airless fan pattern (requires high pressure) |
| Slot tip (ribbon) | One rectangular slot | Slots up to 1 in wide; wider available | 0° | Stainless steel | Thin ribbon, dispensed with the tip in contact with the material |
| Handgun extrusion | One | 0.015–0.050 in | 0° | Stainless steel | Hand-dispensed single dot or bead |
| Extended extrusion | One | 0.006–0.030 in | 0° | Stainless steel | Single dot or bead in a tight space |
Tip type
Single orifice extrusion
Orifices
One
Orifice size
0.006–0.030 in
Angles
0° (on applicator axis)
Material
Stainless steel
Pattern produced
Single dot or bead
Tip type
Multiple orifice extrusion
Orifices
2–6 holes
Orifice size
0.006–0.020 in
Angles
In-line for parallel beads, or radial at a specified angle
Material
Stainless steel
Pattern produced
Group of lines or dots, in-line or radial
Tip type
Side outlet extrusion
Orifices
1, 2, or 3
Orifice size
0.001–0.020 in
Angles
45° and 90° standard
Material
Stainless steel
Pattern produced
Up to 3 lines or dots dispensed perpendicular to the applicator axis
Tip type
Airless spray
Orifices
One
Orifice size
0.009–0.032 in
Angles
15°–110°
Material
Stainless steel or carbide insert
Pattern produced
Airless fan pattern (requires high pressure)
Tip type
Airless spray
Orifices
One
Orifice size
0.009–0.032 in
Angles
15°–110°
Material
Stainless steel or carbide insert
Pattern produced
Airless fan pattern (requires high pressure)
Tip type
Slot tip (ribbon)
Orifices
One rectangular slot
Orifice size
Slots up to 1 in wide; wider available
Angles
0°
Material
Stainless steel
Pattern produced
Thin ribbon, dispensed with the tip in contact with the material
Tip type
Handgun extrusion
Orifices
One
Orifice size
0.015–0.050 in
Angles
0°
Material
Stainless steel
Pattern produced
Hand-dispensed single dot or bead
Tip type
Extended extrusion
Orifices
One
Orifice size
0.006–0.030 in
Angles
0°
Material
Stainless steel
Pattern produced
Single dot or bead in a tight space
Orifice size must not exceed the applicator’s seat size. Our engineering team will confirm the right tip for your fluid, pattern, and applicator.
01
The patented Electromatic™ seat-and-needle geometry eliminates the stringing, drool, and product contamination that plague conventional cold adhesive guns.
02
No packings to wear, no seals to leak, no rebuilds at six-month intervals. The fluid section comes out as a single replaceable unit in seconds.
03
Compatible with the full range of water-based adhesives, latex glues, and aggressive chemistries that degrade conventional components.
04
No trapped areas where adhesive can dry out, char, or accumulate — critical for water-based and latex glues that solidify in dead zones.
05
No external air valves required for the standard Electromatic™ series — instantaneous response and millisecond repeatability for high-speed lines.
06
Full-size and mid-size Electromatic™ applicators are rated for 200 million dispensing shots before refurbishment, and mini applicators for 100 million. Spraymation cold adhesive systems installed 40 or more years ago are still in production today.
07
Accurate, repeatable positive-displacement dispensing for applications that require highly accurate micro deposits — the same metered volume every cycle, independent of line speed.
08
Dots, lines, multiple lines, airless spray, air-atomizing spray, air-dispersed swirl, and slot coating — all from the same Electromatic™ applicator family and the same control architecture.
09
With CE declarations and Low Voltage Directive compliance available for European installations. Family-owned and manufacturing in Fort Lauderdale for more than 60 years, ISO certified for over 20.
Spraymation cold adhesive application equipment is at work across paper converting, hygiene product manufacturing, consumer goods, beverage can production, and dozens of other high-speed converting and assembly operations where consistency and cleanliness matter.
If your cold adhesive application has unusual fluid characteristics, web width requirements, or environmental constraints, our engineering team can design a custom solution — from specialized manifolds to extension-equipped applicators for confined spaces to recirculating-path configurations for fluids that require continuous flow.
Every Spraymation cold adhesive system can be configured with the controls, fluid handling, and accessories needed for a complete turnkey solution.
3480 Pattern Controllers and 3400 Series DC Timers for independent control of up to four applicators with 0.1 ms timing resolution.
Available as a basic single-applicator DELAY/ON timer or a four-channel controller for complex patterns with multiple on/off switching. Supports shaft-encoded position programming in inches — so pattern placement follows actual machine travel rather than elapsed time — and multiple applicators can run from a single timer.
ASME-approved low-pressure tanks in 2, 5, and 10 gallon capacities with optional low-level controls and adjustable-speed agitators, plus portable low-pressure pumps with regulators and tank dollies for mobile applications.
Stainless steel construction, rated to 100 PSI maximum, with DC power supply and CE approval. Accessories include low-level switch, agitator, air gauge, regulator, filter, quick disconnect, and a choice of EPDM or Viton seals for fluid compatibility.
Browse the complete Electromatic™ applicator family for replacement heads, expansion components, or custom configurations across the full product line.
Drivers that supply the optimum voltage and current to get full performance from full-size and mid-size Electromatic™ applicators. Accelerating voltages on both open and close reduce actuation times for higher line speeds. Easy PLC interface, 120 or 240 volt operation.
Stainless steel high-ratio pumps for airless spray and high-viscosity cold adhesive delivery:
Available in wall-mount, 55-gallon drum, and 5-gallon pail configurations. Accessories include control valve, automatic fluid pressure release, air gauge, regulator, and filter.
Quick answers to the questions we get most often about Spraymation cold adhesive systems, Electromatic™ applicators, and fluid handling integration.
Don’t see your question? Our engineering team responds within one business day.
Our cold adhesive systems handle a broad range of materials including water-based glues, latex adhesives, PVA adhesives, marking fluids, perfumes, fragrances, surfactants, low-viscosity silicones, and similar fluids. The Electromatic™ XVI mid-size handles low to medium viscosities up to 6,000 cps, while full-size and air-operated configurations accommodate higher-viscosity and higher-flow requirements. If you have a specific adhesive chemistry, our engineering team can confirm compatibility and recommend the right applicator configuration.
The Electromatic™ applicator at the core of every Spraymation cold adhesive system uses a patented design with only one moving part, no dynamic seals, all-stainless-steel wetted parts, and a positive dripless shut-off. Conventional adhesive application equipment typically relies on packings, dynamic seals, and external air valves that wear, leak, and require frequent rebuilds — and conventional guns are particularly prone to dry-out and clogging with water-based adhesives. Our straight-line flow design eliminates these failure modes, which is why Spraymation cold adhesive equipment routinely stays in production for decades.
Yes. Used with appropriate extrusion tips or spray nozzles and a Spraymation 3480 Pattern Controller or 3400 Series DC Timer, Electromatic™ applicators place dots, continuous lines, interrupted lines, multiple parallel lines, or full atomized spray patterns with extreme accuracy. The full pattern range across the platform covers dots, lines, multiple lines and dots, airless spray, air-atomizing spray, air-dispersed swirl, and slot coating. The Electromatic™ XV is configured for extrusion or airless spray, the XXIV handles air-atomized spray from fine mist to wet coat, and the XX and XXV series handle multiple parallel outlets for wide-web applications.
Capability depends on the specific applicator. The Electromatic™ XVI mid-size handles low to medium viscosities up to 6,000 cps at operating pressures under 2,000 PSI. Full-size Electromatic™ XV applicators handle broader ranges including higher-viscosity cold materials. Air-operated high-volume variants are available for pressures up to 5,000 PSI and very high flow rates with the highest viscosities. Contact our engineering team with your fluid viscosity and we’ll recommend the right configuration.
Yes — custom cold adhesive application equipment is a core part of what we do. We routinely build multi-head manifolds with specified or adjustable center distances for wide-web applications, applicators with extensions for confined-area access such as inside beverage cans, recirculating-path configurations for fluids requiring continuous flow, and one-of-a-kind systems for applications other manufacturers won’t take on. Send us your line speed, web width, fluid specifications, and pattern requirements and our engineering team will recommend a solution.
The Electromatic™ design dramatically simplifies maintenance — the entire fluid section can be removed and replaced as a unit in seconds without taking the gun off the line, and there are no packings or dynamic seals to degrade and replace. We maintain an extensive inventory of spare parts and supplies, offer factory rebuild and gun exchange programs, and provide remote technical support by phone, email, and Zoom, with on-site service available when needed.
Most cold adhesive applications use either a pressure tank or a pumping system depending on viscosity, required flow rate, and operating pressure. Spraymation offers ASME-approved low-pressure tanks in 2, 5, and 10 gallon capacities with optional low-level controls and adjustable-speed agitators for water-based and latex adhesives that require continuous mixing. Tanks are stainless steel, rated to 100 PSI, CE approved, and available with EPDM or Viton seals depending on fluid compatibility. Portable low-pressure pumps with regulators are available for spray applications, and tank dollies provide mobility for shared-use installations. For high-pressure airless spray, our stainless steel balanced-ratio pumps are rated for continuous duty up to 2,500 PSI, in 50:1, 28:1, and 5:1 ratios and wall-mount, drum, or pail configurations.
In most cases, yes. The 3480 Pattern Controller and 3400 Series DC Timers accept inputs from passive contacts, DC voltage signals, photocells, and open collectors, which covers the vast majority of production line control architectures. For specialized control integration, our engineering team can design custom control packages, including stainless steel enclosures and DIN-format temperature controllers.
Full-size and mid-size Electromatic™ applicators are rated for 200 million dispensing shots before factory refurbishment. Mini applicators are rated for 100 million shots, and handguns for 50 million. Those figures are a function of the core design — one moving part, no dynamic seals or packings, and all-stainless-steel wetted parts — and they’re the reason Spraymation cold adhesive systems installed 40 or more years ago are still in production today. When refurbishment does come due, we offer factory rebuild and gun exchange programs.
Spraymation manufactures single-orifice extrusion tips (0.006–0.030 in), multiple-orifice extrusion tips in 2 to 6 holes (0.006–0.020 in), side-outlet tips that dispense perpendicular to the applicator axis in 45° and 90° configurations, airless spray tips (0.009–0.032 in) in fan angles from 15° to 110°, slot tips for ribbon dispensing in widths up to 1 inch and wider on request, handgun extrusion tips (0.015–0.050 in), and extended extrusion tips for dispensing into tight spaces. All are stainless steel, with carbide inserts available on airless spray tips. Orifice size cannot exceed the applicator’s seat size — send us your fluid, pattern, and applicator and we’ll confirm the right tip.
A low-pressure system feeds applicators from an ASME stainless steel pressure tank rated to 100 PSI, which suits lower-viscosity fluids, lower flow rates, and applications that benefit from agitation. A high-pressure system uses a stainless steel high-ratio pump — 50:1 at 1.25 gal/min and 2,500 PSI, 28:1 at 2.0 gal/min and 2,500 PSI, or 5:1 at 4 gal/min and 500 PSI — and is required for airless spray and for higher-viscosity or higher-flow applications. Viscosity, required flow rate, and operating pressure determine which is right for your line.
Yes. A single Spraymation timer can drive multiple applicators, and our four-channel controllers handle complex patterns with multiple on and off points per cycle. For applications where pattern placement has to follow machine travel rather than elapsed time, shaft-encoded position programming lets you program placement in inches. Systems can also run directly from your existing PLC.
Get Started
Talk to a Spraymation engineer about the right Electromatic™ applicator, fluid handling, and pattern control configuration for your line. We’ll help you specify a system that eliminates waste, prevents bond failures, and stays in service for decades.
Or call us directly +1 954 484 9700